Zeiss LSM 510 META Especificaciones Pagina 229
- Pagina / 330
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
OPERATION
LSM 510 Annex
B 40-051 e 07/98 4-171
4.12.2 Filter change in the detection beam path of channels 1 and 2
For optimum investigation of specimens it is useful to employ filter wheels permitting motor-controlled
change between different filters for narrow-band or broad-band detection depending on the wave-
length. The number of filters is limited by the capacity of the filter wheel. The change of the filter wheel
as a whole involves complete readjustment.
The filter wheels of channels 1 and 2 of the Scanning Module have a change position in which a filter,
including its mount, can be changed in a reproducible position without requiring readjustment. The
filters can be rotated in their cells, and with the light path being eccentric relative to the filter center, the
best transmission area of the filter for the respective wavelength or pass range can be found by rotating
the filter. This is very important for the investigation of specimens of low emission.
Filter change
By software control, move filter wheel (4-1/5)
to the change position.
Pull cover cap (4-1/1) off the Scanning Module.
Use the wire stirrup (4-1/2) to pull the filter
mount (4-1/4) with the filter (4-1/3) out of the
guide well.
Change filter to suit the application.
☞
The filter is rotatable in its mount,
allowing adjustment for finding the
best transmission area of the filter for
the wavelength used.
Enter the designation of this particular filter into
the System Software database.
3
5
4
2
1
Fig. 4-170 Filter change
- Laser Scanning Microscope 1
- B 40-051 e 07/98 III 3
- IV B 40-051 e 07/98 4
- Scope of Equipment Supplied 6
- INTRODUCTION 10
- X B 40-051 e 07/98 10
- CONTENTS 11
- NOTES ON DEVICE SAFETY 12
- Contents LSM 510 12
- 1-2 B 40-051 e 07/98 12
- 1 NOTES ON DEVICE SAFETY 13
- Exit aperture 18
- B 40-051 e 07/98 1-9 19
- 1-10 B 40-051 e 07/98 20
- LGK 7774 21
- LGK 7628-1 21
- 1-12 B 40-051 e 07/98 22
- LSM 510 - SETUP REQUIREMENTS 24
- 2-2 B 40-051 e 07/98 24
- Fig. 2-1 25
- Fig. 2-2 25
- Fig. 2-3 26
- Fig. 2-4 27
- 2-12 B 40-051 e 07/98 34
- CHAPTER 3 INTRODUCTION TO 35
- LASER SCANNING MICROSCOPY 35
- 3-2 B 40-051 e 07/98 36
- Module VIS 40
- Scan ModuleMicroscope 40
- Module UV 40
- 3-12 B 40-051 e 07/98 46
- CHAPTER 4 OPERATION 59
- 4 OPERATION 61
- Fig. 4-1 62
- Fig. 4-2 63
- Fig. 4-3 63
- Fig. 4-4 64
- Fig. 4-5 65
- Fig. 4-6 66
- Fig. 4-7 66
- Fig. 4-8 67
- Fig. 4-9 67
- Fig. 4-10 68
- Fig. 4-11 69
- Fig. 4-12 70
- Fig. 4-13 71
- Fig. 4-14 72
- Fig. 4-15 73
- Fig. 4-16 74
- Fig. 4-17 75
- Fig. 4-18 76
- Fig. 4-19 77
- Fig. 4-20 78
- Fig. 4-21 79
- Fig. 4-22 80
- Fig. 4-23 82
- Fig. 4-24 82
- Fig. 4-25 83
- Fig. 4-26 83
- Fig. 4-27 83
- Fig. 4-28 84
- Fig. 4-29 84
- Fig. 4-30 85
- Fig. 4-31 86
- Fig. 4-32 88
- Fig. 4-33 89
- Fig. 4-34 90
- Fig. 4-35 90
- Fig. 4-36 91
- Fig. 4-37 92
- Fig. 4-38 93
- Fig. 4-39 95
- Fig. 4-40 96
- Fig. 4-41 97
- Fig. 4-42 98
- Fig. 4-43 100
- Fig. 4-44 101
- Fig. 4-45 103
- OPERATION 104
- 4-46 B 40-51 e 07/98 104
- B 40-051 e 07/98 4-47 105
- Fig. 4-48 106
- Fig. 4-49 107
- Fig. 4-50 108
- Fig. 4-51 109
- Fig. 4-52 110
- Fig. 4-53 111
- Fig. 4-54 112
- Fig. 4-55 113
- Fig. 4-56 114
- Fig. 4-57 115
- Fig. 4-58 115
- Fig. 4-59 116
- Fig. 4-60 117
- Fig. 4-61 118
- Fig. 4-62 119
- Fig. 4-63 120
- Fig. 4-64 121
- Fig. 4-65 122
- Fig. 4-66 123
- B 40-051 e 07/98 4-67 125
- Fig. 4-68 126
- Colored marker positions 126
- Fig. 4-69 127
- Fig. 4-70 128
- Fig. 4-71 129
- Fig. 4-72 129
- Fig. 4-73 130
- Fig. 4-74 130
- Fig. 4-75 131
- Fig. 4-76 131
- Fig. 4-77 132
- Fig. 4-78 133
- Fig. 4-79 133
- Fig. 4-81 134
- Fig. 4-80 134
- Fig. 4-82 135
- Fig. 4-83 135
- Fig. 4-90 139
- Fig. 4-91 140
- LSM 510 Image Optimization 141
- B 40-051 e 07/98 4-83 141
- Fig. 4-93 142
- Fig. 4-94 143
- Fig. 4-95 144
- B 40-051 e 07/98 4-87 145
- Fig. 4-97 146
- Fig. 4-98 147
- Fig. 4-99 148
- Fig. 4-100 149
- Fig. 4-101 150
- Fig. 4-102 151
- Fig. 4-103 152
- Fig. 4-104 153
- / Ampl. Gain 154
- Fig. 4-105 155
- Fig. 4-106 156
- Fig. 4-107 157
- Fig. 4-108 158
- Fig. 4-109 159
- Fig. 4-110 160
- Fig. 4-111 161
- Fig. 4-112 162
- Fig. 4-113 163
- Fig. 4-114 164
- Fig. 4-115 164
- Fig. 4-116 165
- Fig. 4-117 166
- Fig. 4-118 168
- Fig. 4-119 169
- Fig. 4-120 170
- Fig. 4-121 171
- Fig. 4-122 172
- Fig. 4-123 173
- Fig. 4-124 174
- Fig. 4-125 175
- Fig. 4-126 176
- Fig. 4-127 177
- Fig. 4-128 178
- Fig. 4-129 179
- Fig. 4-130 180
- Fig. 4-131 181
- 4-124 B 40-051 e 07/98 182
- Fig. 4-133 183
- Fig. 4-134 185
- Fig. 4-135 186
- Fig. 4-136 187
- Fig. 4-137 188
- Fig. 4-138 188
- Fig. 4-139 189
- Fig. 4-140 190
- Fig. 4-141 191
- 4-134 B 40-051 e 07/98 192
- Fig. 4-143 193
- Fig. 4-144 194
- B 40-051 e 07/98 4-137 195
- Fig. 4-146 196
- Fig. 4-147 196
- Fig. 4-148 198
- Fig. 4-149 199
- Fig. 4-150 199
- Fig. 4-151 199
- Fig. 4-152 200
- Fig. 4-153 201
- Fig. 4-154 202
- Fig. 4-155 203
- Fig. 4-156 203
- Fig. 4-157 204
- Fig. 4-158 205
- Fig. 4-159 206
- Fig. 4-160 206
- Fig. 4-161 207
- Fig. 4-162 207
- Fig. 4-163 209
- Fig. 4-164 210
- Fig. 4-165 212
- Fig. 4-166 214
- Fig. 4-167 215
- Fig. 4-168 216
- Fig. 4-169 217
- LSM 510 Annex 219
- B 40-051 e 07/98 4-161 219
- Annex LSM 510 220
- 4-162 B 40-051 e 07/98 220
- B 40-051 e 07/98 4-163 221
- 4-164 B 40-051 e 07/98 222
- B 40-051 e 07/98 4-165 223
- 4-166 B 40-051 e 07/98 224
- B 40-051 e 07/98 4-167 225
- 4-168 B 40-051 e 07/98 226
- B 40-051 e 07/98 4-169 227
- 4-170 B 40-051 e 07/98 228
- Fig. 4-170 Filter change 229
- Allen key 230
- B 40-051 e 07/98 4-173 231
- Fine focusing 233
- Fig. 4-173 234
- Fig. 4-174 237
- Fig. 4-175 240
- Fig. 4-176 246
- Fig. 4-177 247
- Fig. 4-178 249
- Fig. 4-179 250
- Fig. 4-180 252
- Fig. 4-181 253
- CHAPTER 5 3D FOR LSM 510 255
- 5-2 B 40-051 e 07/98 256
- Positive rotation directions 257
- Fig. 5-1 257
- Fig. 5-2 259
- Display window 260
- Fig. 5-4 265
- Fig. 5-5 267
- Fig. 5-6 268
- Fig. 5-7 270
- Fig. 5-9 274
- Fig. 5-10 275
- Fig. 5-11 276
- Fig. 5-12 278
- Fig. 5-13 280
- Fig. 5-14 283
- Fig. 5-15 285
- Fig. 5-16 287
- Fig. 5-17 288
- Fig. 5-18 291
- Fig. 5-19 291
- Fig. 5-20 292
- Fig. 5-21 293
- Fig. 5-22 295
- Fig. 5-23 297
- Fig. 5-24 299
- Fig. 5-25 301
- Fig. 5-26 303
- Fig. 5-27 304
- Fig. 5-28 305
- Fig. 5-29 306
- Fig. 5-30 307
- Fig. 5-31 308
- Fig. 5-32 309
- Fig. 5-33 310
- Fig. 5-34 314
- Functions LSM 510 318
- 5-64 B 40-051 e 07/98 318
- Measurement Concept 318
- Fig. 5-36 319
- Fig. 5-37 320
- Fig. 5-39 327
- Measured 329
- Object Features 329
- Volume Features 329
Relacionado con productos y manuales para Microscopios Zeiss LSM 510 META
Microscopios Zeiss LSM 510 META Manual de usuario
(17 paginas)
(17 paginas)
Microscopios Zeiss N HBO 103 Especificaciones
(120 paginas)
(120 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales